Discovering Plumbing Basics is Essential When Installing a Bathtub
Discovering Plumbing Basics is Essential When Installing a Bathtub
Blog Article
The publisher is making a few good pointers related to How to Install a Bathtub Yourself in general in the content following next.
Setting up a bathtub isn't specifically rocket science, however it does require solid plumbing, woodworking, and also often, tiling skills. Changing an old bath tub with a new one is likewise a reasonably hard project. If the old bathtub is conveniently obtainable, the job can relocate speedily; if you have to open up a wall surface to get rid of the old bathtub and position the new bathtub, the job is a lot harder. In either case, the job is within a home handyman's abilities, although you will certainly need a helper to leave the old tub and also set in the new one. Ensure you have certified yourself for the job as well as fit attempting it. Instead of hiring a contractor to take over a halfway-completed task, it is far better to take into consideration utilizing one prior to you begin. Possibilities are you might require a specialist plumber to make tube connections.
This short article will assist you install a new tub in your restroom if you have already gotten a new bathtub and don't require to transform the arrangement of your previous water pipelines.
Your devices as well as product list need to make up the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you ought to do is separate the water system. After doing so, switch on the taps to drain pipes any water remaining in the system. The procedure of eliminating the existing taps can be quite problematic due to the limited gain access to that is commonly the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the faucets. Have a cloth prepared for the continuing to be water that will certainly originate from the pipelines. Once the supply pipes have been gotten rid of, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary faucets from transforming during this process. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing substance.
Prior to going on to fit the new taps, contrast the pipeline connections on the old taps to the new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will need a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the faucet and also the various other end gives a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly call for lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, place the tap in the placing hole in the bath/basin ensuring that the washers are in location between the tap as well as the sink. Protect the tap in position with the manufacturer supplied backnut. When the faucet is safely in position, the supply pipes can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical tap connectors. The former kind needs to be attached to the faucet ends initially, tightening up only by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Installing the Bathtub
Making use of the two wooden boards under its feet, place the bath tub in the needed position. The wood boards are handy in equally spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 small factors.
The following objective is to guarantee that the bathtub is leveled all round. This can be accomplished by checking the spirit level as well as adjusting the feet on the bathtub up until the level reads level.
To set up taps, fit all-time low of the outermost adaptable tap port to the suitable supply pipe by making a compression join; after that do the very same for the other tap.
Activate the water system and examine all joints and also new pipework for leaks and tighten them if required. Load the tub and also inspect the overflow outlet and also the normal electrical outlet for leakages.
Lastly, fix the bathroom paneling as defined in the maker's instruction manual. Tiling as well as sealing around the tub needs to wait up until the bathtub has actually been utilized at least when as this will settle it right into its final position.
Planning for the Installation
First of all, the supporting structure provided with the bathroom needs to be fitted (if required) according to the manufacturer's directions. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is necessary to make certain that if the tap features a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is additionally practical to fit a supporting plate under the taps device to stop strain on the bath tub.
Fit the flexible tap adapters to the bottom of both taps using 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you make use of all of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath ought to now prepare to be suited its final setting.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to break a rigid seal, causing the water to pass through the wall in between the bathroom as well as the tiling, bring about issues with moisture and possible leaks to the ceiling listed below.
You can select from a range of coloured sealers to assimilate your fixtures and fittings. They are marketed in tubes and cartridges, and also are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched paper or soft rope. Bear in mind to always fill the tub with water before sealing, to permit the activity experienced when the tub is in use. The sealant can break relatively very early if you do not think about this activity before sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also conveniently readily available on the marketplace. It is suggested to fit the floor tiles utilizing water-resistant or waterproof sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that write up about Installing A Bathtub while doing a search on the internet. For those who enjoyed our blog post please make sure you remember to share it. Many thanks for your time. Please check our blog back soon.
We're on standby! Report this page